When using industrial forklifts, should the load be in the lowest position?
When the load is moved upward, the forklift’s center of gravity shifts forward. A safe load that is 4 inches off the ground can tip the forklift over when lifted 4 feet. This is why OSHA training documents instruct operators to always "carry the load to the lowest possible position, 4 to 6 inches off the ground"
When using industrial forklifts, the load must be in the lowest position for travel, and the forklift manufacturer’s operating requirements&>39C must be followed. Which regulation states that materials must be stacked at the same level? “
§ 1926.250 General storage requirements. (a) General Provisions. (1) All materials stored in tiers shall be stacked, racked, blocked, interlocked, or otherwise secured to prevent sliding, falling, or collapsing.
When a forklift is in motion, the load being transported shall be in the highest possible position during the motion True or false?
Transport the load in the lowest possible position, 4-6 inches off the ground.
How high should the load be when the forklift is moving?
When moving the load, keep the forks 6-10 inches off the ground to avoid potential hazards on the ground. Remember that forklifts have a large weight capacity. Carry the load low and with a backward tilt. Be careful when carrying a load over uneven ground – this creates a tipping hazard.
What are the three basic steps of a job safety analysis?
What are the four basic steps?
- select the job to analyze.
- break the job into a sequence of steps.
- identify potential hazards.
- identifying preventive measures to overcome these hazards.
<
What is OSHA’s Hazardous Process Analysis Standard? “
Hazardous Process Analysis is a thorough, orderly, systematic approach to identifying, evaluating, and controlling the hazards of processes involving highly hazardous chemicals. The employer shall conduct an initial process hazard analysis (hazard assessment) for all processes covered by this standard.
What is the highest height-to-base ratio when stacking materials? “
4:1 A good rule of thumb for stack stability is to maintain a height-to-base ratio that does not exceed 3:1 (or a maximum of 4:1 if the stack is effectively interlocked and there is good adhesion between the contacting surfaces).
What is the maximum height of the stack – No more than 16 feet if you pile each item on top of the other without the aid of a machine. With equipment such as a forklift, this figure increases to 20 feet.
What is the maximum load torque for a forklift? You can determine the maximum load torque of your forklift by multiplying its rated weight by the distance between load centers, which can be found on the machine’s data plate. For example, if your forklift weighs 4,000 pounds and has a 24-inch load center, its load capacity would be 96,000 inch-pounds.
Where should the heaviest part of the load be located on the forklift? “
Where should the heaviest part of the load be located on the forklift? “
[29 CFR 1910.178(o)(1)] Distribute the heaviest part of the load closer to the front wheels of the forklift. Do not allow overloading. Know the stated load capacity of the forklift and do not exceed it. [29 CFR 1910.178(o)(2)] Only by following the weight limits will you be able to operate the forklift safely.
What is step 3 of the risk analysis?
The main purpose of this step in the HSE&>39;Management Standards approach is to collect and analyze the data from the previous step, discuss the findings with a representative sample of employees, and develop solutions with them.
What are the 5 steps of a job analysis?
Steps in the job analysis process
- Planning a job analysis. ….
- Preparing and implementing the job analysis. ….
- Performing a job analysis. … .
- Developing job descriptions and job specifications. … …
- Maintaining and updating job descriptions and job specifications.
<
What is a high hazard process? “
“Process means any activity involving highly hazardous chemicals, including any use, storage, manufacture, handling, or movement of such chemicals on site, or a combination of these activities.”
